White sectional garage door closed tight against a Kentucky driveway

Garage Door Weather Seal Replacement in Andover Forest, KY

On the brick homes along Forest Hill Drive, garage door weatherstripping in Andover Forest starts with the bottom seal against the slab. We fit a new seal to the retainer and replace worn perimeter strips along the jambs.

We fit new bottom seals for Andover Forest doors near Forest Hill Drive.

Get Your Free Weather Seal Quote

Bottom seal, perimeter, and threshold • No-obligation quote

Step 1 of 2
Required field
Required field
Required field

Seal check

6 Signs Your Garage Door Seals Have Failed

  • 01
    Daylight under or around the closed doorStand inside with the door closed and the lights off. Light at the floor means the bottom seal has flattened, split, or no longer reaches an uneven slab; light at the sides or top means the perimeter stop molding has pulled away or hardened.Light at the floor or edges means a seal has failed.
  • 02
    A cracked, brittle, flattened, or torn bottom sealVinyl and rubber harden with sun, salt, and freeze-thaw cycles. A seal that no longer springs back, shows splits at the ends, or has worn through to the retainer is no longer sealing.A hardened, split or worn-through seal no longer seals.
  • 03
    Water, leaves, or grit coming in at the floorA seal that lifts on one side or a slab that has settled lets wind-driven rain and debris under the door. Puddles near the edge, damp cardboard, or a tide line on the concrete are the usual tells.A lifted seal or settled slab lets rain and debris in.
  • 04
    Drafts, cold floors, or a garage that swings with the weatherThe bottom and perimeter seals are the largest gap in the garage envelope. When they fail, an attached garage loses conditioned air, and the rooms above and beside it feel it.Failed seals let conditioned air out of the garage.
  • 05
    Mice, insects, or spiders finding their way inA quarter-inch gap is enough for a mouse. Chewed seal ends and droppings along the door line point to an entry at the bottom corners or where the seal meets the jamb.A quarter-inch gap is enough for a mouse.
  • 06
    The retainer or stop molding is bent, loose, or rottedA bottom seal is only as good as the aluminum or PVC retainer that holds it, and perimeter weatherstrip depends on sound jambs. Damaged retainers and rotted wood stops need correcting, not just a new strip.Bent retainers or rotted stops need repair, not just a strip.

What to do now

Do the light test tonight. Then tell us what you saw.

Close the door, turn off the garage lights, and look along the floor and up both sides. Note where the light shows: bottom, one corner, the sides, or the top, and whether the floor looks uneven. That tells us whether you need a bottom seal, perimeter stop molding, a threshold, or all three, and we can usually bring the right profile on the first visit.

Split, brittle garage door bottom seal with daylight showing through
A split, hardened bottom seal lets light, water, and pests in at the floor. It is the most common seal failure we see.

Customer reviews

Kentucky homeowners recommend Derby Strong.

Understand your options

Choose the right seal for your garage

Know the seals

Bottom Seal vs. Perimeter Weatherstrip: Which One Is Leaking?

Along the floorBottom seal
Up the sides and across the topPerimeter weatherstrip
What it is A rubber or vinyl strip seated in the aluminum or PVC retainer on the door’s lower edge Vinyl stop molding with a flexible fin nailed or screwed to the jambs and header
What it stops Water, wind, grit, insects, and mice at the floor, the largest gap on the door Side and top drafts, driving rain, dust, and the rattle of the door against the stops
Sign it failed Daylight at the floor, a flattened or split strip, puddles or tide lines inside Light at the edges, a hardened or curled fin, a gap between molding and door face
Styles and profiles T-end, bead, U-shape, bulb; standard or oversized; rodent-resistant with mesh core Vinyl stop molding with fin; solid or hollow; white, brown, or color-matched
Along the floor

Bottom seal

Rubber or vinyl fitted into the retainer on the door’s lower edge.

Stops
Water, wind, grit, insects, and mice at the floor.
Replace when
You see daylight, splits, flattening, or water lines inside.
Common profiles
T-end, bead, U-shape, bulb, and rodent-resistant.
Sides and top

Perimeter weatherstrip

Vinyl stop molding with a flexible fin fitted to the jambs and header.

Stops
Side and top drafts, rain, dust, and door rattle.
Replace when
You see edge light, a curled fin, or a gap beside the door.
Common profiles
Solid or hollow vinyl in white, brown, or matched colors.

Uneven floor? That is what a threshold seal is for.Uneven floor? Add a threshold.

A raised rubber threshold bonded to the concrete gives the bottom seal something level to land on, turns water away from a slab that slopes toward the garage, and closes a low corner no bottom seal can reach. It is added to a bottom seal, not substituted for it.A bonded rubber threshold gives the bottom seal a level surface and helps turn water away. It works with—not instead of—the bottom seal.

Not sure what you have? Send a photo of the bottom corner of the closed door from inside, and a close-up of the retainer edge if you can reach it safely. We can usually identify the profile before the visit.

The complete seal

Three Seals That Close the Garage Door Envelope

01

Bottom seal with retainer

The single most important seal on the door. A compressible rubber or vinyl strip seated in the bottom retainer closes the gap to the floor against water, air, and pests. Oversized profiles handle uneven slabs; rodent-resistant versions add a metal mesh core.Closes the floor gap against water, air and pests.

02

Perimeter weatherstrip (stop molding)

Vinyl stop molding with a flexible fin runs up both jambs and across the header. It seals the side and top gaps, blocks drafts and driving rain, and keeps the door from rattling against the stops.Seals the side and top gaps and stops door rattle.

03

Threshold seal

A raised rubber barrier bonded to the concrete where the door closes. It is the answer when the slab slopes toward the garage, water tracks in under the seal, or the floor is too uneven for a bottom seal alone.A floor barrier for sloped or uneven slabs.

Seal selection

The Four Things We Match Before Fitting a Seal

  1. 01

    Retainer profile and seal style

    Bottom seals come in T-end, bead, U-shape, and bulb styles, each made for a specific retainer channel. We match the profile to your door’s retainer rather than forcing a near-fit that leaks at the ends or pulls out of the track.We match the seal profile to your retainer.

  2. 02

    Floor condition

    Many Kentucky garage slabs have settled, cracked, or sloped toward one corner. An oversized or U-shape seal fills a low spot; a badly uneven floor may also call for a threshold seal bonded to the concrete.We check the slab for slopes and low spots.

  3. 03

    Perimeter stop molding and jambs

    Vinyl stop molding with an integral flexible fin seals the sides and top. We check the fin for hardening and the jambs for rot, and set the molding so it touches the door face without dragging.We check the side and top fins and the jambs.

  4. 04

    Material for the climate

    EPDM rubber stays flexible through Kentucky winters where thin vinyl turns brittle; silicone lasts longest. Solid versus hollow trim, black versus gray, and rodent-resistant seals with a mesh core are chosen for the exposure the door sees.Flexible material, rodent-resistant where needed.

Why the ends matter: most do-it-yourself bottom seals fail at the corners, where the strip was cut flush and shrank back, leaving the exact gap a mouse or a stream of water needs. We leave extra length and fold it into the retainer at each end, then re-check the opener’s travel limit so it does not crush the thicker new seal.Corner fit matters. We fold extra seal into both ends, then check the opener so the new seal is not crushed.

Worn garage door bottom seal with a visible gap and daylight below Worn · Gap and daylight at the floor
Technician fitting a new rubber bottom seal on a white garage door New · Seal fitted to the retainer
A flattened seal that has pulled away from the floor, and a new seal being fitted into the retainer where it can compress against the slab.

Service and pricing

What Seal Replacement Includes—and What It May Cost

Four clear stepsHow installation works

  1. 01

    Inspect the whole door edge

    The technician checks the bottom seal and retainer, the perimeter stop molding and jambs, the header seal, and the floor line for gaps, wear, rot, and water tracks.We check the bottom, sides, top, retainer, and floor for gaps or damage.

  2. 02

    Match the seal to the door

    Profile, size, and material are selected for your retainer, door width, and floor condition, so the new seal seats correctly and seals at the ends.We match the profile and material to your door, retainer, and floor.

  3. 03

    Replace, reseat, and set

    Old material is removed, the retainer or stop molding is repaired or replaced where needed, and the new seal is fitted with extra length folded at the ends rather than cut short.We remove the old material, make needed repairs, and fit the new seal.

  4. 04

    Close, test, and check the light

    The door is closed and checked from inside for daylight, the seal contact is verified across the full width, and the travel limits are confirmed so the opener does not crush the new seal.We close the door, check for light, and confirm even contact and travel.

Garage door weatherstripping across Andover Forest

Mornings in Andover Forest run humid for much of the year, and freezing nights follow each winter. On a brick house along Forest Hill Drive or in Andover Heights, the garage door is the widest opening in the wall. Only rubber seals close its edges. A worn bottom seal lets that damp air in at the floor.

The bottom seal does most of the work, closing the gap between the door and the slab. Over time it flattens, cracks or pulls out of its retainer. Homes along Hays Boulevard were built years apart, so one door's seal can be original while the next is new. Along the sides and top, a perimeter seal presses against the door to block drafts. We replace worn weatherstripping and fit the new bottom seal to the floor.

Service area coverage

Local ZIP: 40509

Open in Google Maps

Before you schedule

Answers to Common Garage Door Seal and Weatherstrip Questions

Bottom seal seated in its retainer and meeting the concrete floor
Bottom seal
T-end, bead, U-shape, or bulb; must match the retainer channel
Retainer
Aluminum or PVC channel on the door’s lower edge that holds the seal
Stop molding
Vinyl perimeter weatherstrip with a flexible fin on both jambs and the header
Threshold
Rubber barrier bonded to the floor for sloped or uneven slabs
Seals at a glanceThe four parts that close the gap around a sectional door.
01What is the price of replacing a garage door weather seal in Andover Forest?

Vinyl stop molding, replaced down both sides and along the header, usually runs $150–$275. A bottom seal costs $95–$165 installed on a single door and $125–$195 on a double door. Threshold seals mounted on the floor run $110–$195. Repairing a damaged bottom retainer or a rotted jamb adds to the job, and that part is quoted before work begins. Most of the time, the best value is to replace the bottom seal and perimeter together in one visit.

02Which type of bottom seal does my garage door take: T-end, bead, U-shape, or bulb?

It is set by the retainer your door already has. T-end seals are made for the most common aluminum retainer channel and slide right in. Many steel doors use a round-channel retainer, and that calls for a bead seal. U-shape and bulb seals suit an uneven floor or a spot that needs a thicker profile. Show us a photo of the retainer edge or a leftover scrap of the old seal, so we can match it before the visit.

03How long before garage door seals wear out?

Roughly three to eight years is typical for most bottom seals and weatherstrips. Several things shorten it: strong sun, road salt, freeze-thaw cycles and the number of times the door closes. In cold weather, thin vinyl becomes brittle first. EPDM rubber holds up longer, and silicone has the longest life. An inspection each year before winter will flag a seal that is nearly worn out.

04What causes a gap to remain after the bottom seal is replaced?

Most often it is the floor, not the seal. Slabs settle, crack and slope, and a low corner can sit beyond the reach of a standard seal. The options are a threshold seal bonded onto the slab, an oversized or U-shape seal for the low area, or the two together. When only one side shows a gap, the door may be sitting out of level. That is a cable or track issue, not a seal issue.

05Is a bottom seal replacement a DIY job?

It can be. For a standard steel door that has a sound retainer and sits on a level floor, it is among the more DIY-friendly garage door tasks. Get the profile right for the retainer, since the wrong one is a common mistake. Leave extra at both ends to fold instead of cutting the seal flush. Afterward, check the opener's travel limit again; if it is left alone, the opener can crush the thicker new seal. Bring in a professional when water gets in regularly, the jambs are rotted, the retainer is bent, or rodents find a way through.

06What separates the bottom seal from the weatherstripping?

They seal different edges. Weatherstripping, also known as stop molding, is vinyl trim along both sides and the top of the opening. Its flexible fin seals against the face of the door. The bottom seal is different: it is fastened to the door's lower edge and touches the floor. Most draft and water problems come down to the bottom seal, while rattles and side drafts usually involve the stop molding around the perimeter.

07Will replacing the seals stop mice getting in?

They help by closing the bottom corners and the joint between seal and jamb, where mice most often get through. Where a garage has a history of rodents, pick a bottom seal built to resist them. Its metal mesh core holds up against chewing. The stop molding around the perimeter should also be fitted tight to the jambs. Seals are one piece of pest control rather than the whole answer.

08Are garage door seals worth it for energy use?

On an attached garage, yes. It is joined to the living space by shared walls, and often a shared ceiling. Meanwhile, the door perimeter is the largest gap in the garage left uncontrolled. Sound seals keep conditioned air from escaping and stop wind from coming in. That steadies the temperature in the garage and supports an insulated door in doing its job. Seals are also the lowest-cost part of the door to get right.

09How do I choose between black and gray, or solid and hollow seals?

Black seals absorb more heat, so they fit cold areas; gray ones stay cooler where the sun is strong. Solid profiles are for colder regions and hollow profiles for warmer regions. For the majority of Kentucky doors, standard vinyl stop molding is the right fit, together with a flexible EPDM bottom seal in either color. We match that pairing to the door's exposure.

10Will the door close the same way with a new seal?

Not always. The new seal is thicker than the old one, which had flattened. If the opener's travel limit was set for that old seal, it may stop the door short or reverse it. Once the seal is installed, we check and reset the limit. That way the door closes fully and the safety reversal keeps working.

11When is it time to replace my garage door seals?

Worn seals show themselves in a few ways. With the door closed, light gets through underneath or around the sides. Drafts come in at the floor, and wind carries in water or leaves. The seal looks cracked, flattened or brittle. Another frequent sign is mice in the garage, which shows the bottom seal is no longer touching the floor.

Local help for a drafty, leaking, or pest-prone door

Tell us where the light shows. We’ll bring the right seal.

Let us know whether it is a single or double door, where you see light or water at the bottom, sides, or top, whether the floor looks uneven, and whether you have had pests. We will confirm the materials and price before work begins.

  • Single or double door
  • Light or water at the bottom, sides, or top
  • Uneven floor, pests, or rotted trim
Call (859) 436-2954

Request Weather Seal Service

Serving Andover Forest and nearby Lexington communities. Share the essentials and we’ll call to confirm the right service timing.

Step 1 of 2
Required field
Required field
Required field

Derby Strong Garage Doors

Garage door trouble?

Talk to our local team now about a broken spring, a stuck door, an opener or a new door.

Call (859) 436-2954 Schedule online

5.0 from 298 reviews